u-i4-6264 | Pro Spot Refurbished i4 Spot Welder | Reconditioned
A reconditioned pre-owned Pro Spot i4 inverter resistance spot welder — water-cooled, three-phase, built for boron and advanced high-strength steels. Traded in in working order, then inspected, serviced, and weld-tested by CRTE technicians. Complete standard equipment set, stocked accessory tray with fresh consumables, plus the optional C-to-X adapter. One available — photos show the actual unit.
Choose Quantity
Reconditioned Pre-Owned Pro Spot i4 Resistance Spot Welder — i4-6264
This Pro Spot i4 (serial i4-6264) came to us as a trade-in in working order and has been through our full reconditioning process — inspected, serviced, cleaned, and weld-tested by CRTE technicians before listing. We don't distribute the i4 new; we take them in on trade, recondition them, and stand behind them.
The i4 is Pro Spot's inverter-based resistance spot welder, aimed at the high-strength and boron steels of modern unibody construction. It runs a double-acting spot gun on a four-cable system, so a tech can move between two-sided and single-sided work without rebuilding the setup. Electrodes are self-aligning and wide-spreading — an arm swap doesn't cost you a re-alignment. An onboard screen carries repair-procedure content and operator training, and weld software updates by flash card rather than a service call.
In a collision shop the i4 lives in the structural bay doing the everyday squeeze-type resistance welding a modern repair plan calls for, with the arm library covering the awkward geometry — wheelhouses, tight flanges, and closed sections reachable only with the C-to-X adapter. Simple machine, cheap and available consumables, arms that hold their value — a genuinely good used buy for a second structural bay.
What's Included with This Unit
- Double-sided spot gun and arm, with boom-mounted cable support arm assembly
- 80 mm and 500 mm extension arms + 5/8" wheelhouse arm
- 45-degree upper and lower electrodes, electrode and rivet holder
- 60 mm, 20 mm, and 8 mm thumb-screw shanks
- Weld caps (female and male), tightening handle, trigger switch, protection cover
Key Features
- Inverter resistance spot welding rated to 12,500 A on three-phase power
- Double-acting spot gun with self-aligning, wide-spreading electrodes
- Four-cable system for moving between two-sided and single-sided welding
- Single-sided welding with a library of preset programs
- Water-cooled cables and electrodes
- Onboard display with repair-procedure screens and operator training; software updates by flash card
- Optional integrated MIG upgrade and dent-pulling accessories available
- Ceiling-mount installation option to free floor space
Specifications
| Condition | Pre-owned · reconditioned & weld-tested by CRTE |
| Serial | i4-6264 |
| Spot gun | Double-sided spot gun and arm (standard cylinder) |
| Electrode force (standard cylinder)* | 156 daN @ 60 PSI · 236 daN @ 90 PSI · 302 daN @ 116 PSI · 351 daN @ 135 PSI |
| Max welding current* | 12,500 A (three-phase) |
| Input voltage | Three-phase — call to confirm this unit's configuration |
| Cooling | Water-cooled cables and electrodes |
| Welder height* | 50 in (83.25 in with arm assembly) |
| Footprint* | approx. 28 × 12.5 × 50 in |
| Weight* | approx. 373 lbs |
| Extension arm reach* | 500 mm standard |
| Brand | Pro Spot |
| SKU | CRTE-u-i4-6264 |
We can ship anywhere on the planet — call today for a quote! 973-768-9812
Pro Spot and i4 are trademarks of Pro Spot International, Inc. Innovative Solutions CRTE is an independent reseller and is not affiliated with, authorized by, or endorsed by Pro Spot International. This unit is pre-owned and was inspected, tested and reconditioned by Innovative Solutions CRTE. All model specifications, ratings, and capability figures shown are taken directly from the manufacturer's own published documentation and are republished here as-is; Innovative Solutions CRTE has not independently tested these figures and makes no claim as to their accuracy or validity. Any automaker (OEM) program, approval, or requirement referenced likewise reflects the manufacturer's published materials — not a representation by CRTE — applies to the equipment model as manufactured and supported by Pro Spot, and no shop certification transfers to the buyer with the machine. Buyers should confirm current specifications and OEM requirements directly with the manufacturer and the automaker.
